diff --git a/include/configs/HIDDEN_DRAGON.h b/include/configs/HIDDEN_DRAGON.h
index c8c0409..f6777b9 100644
--- a/include/configs/HIDDEN_DRAGON.h
+++ b/include/configs/HIDDEN_DRAGON.h
@@ -77,14 +77,14 @@
 /*
  * Miscellaneous configurable options
  */
-#define CFG_LONGHELP		1		/* undef to save memory		*/
-#define CFG_PROMPT		"=> "		/* Monitor Command Prompt	*/
-#define CFG_CBSIZE		256		/* Console I/O Buffer Size	*/
-#define CFG_PBSIZE (CFG_CBSIZE+sizeof(CFG_PROMPT)+16)	/* Print Buffer Size	*/
-#define CFG_MAXARGS		16		/* max number of command args	*/
-#define CFG_BARGSIZE		CFG_CBSIZE	/* Boot Argument Buffer Size	*/
-#define CFG_LOAD_ADDR		0x00100000	/* default load address		*/
-#define CFG_HZ			1000		/* decrementer freq: 1 ms ticks */
+#define CONFIG_SYS_LONGHELP		1		/* undef to save memory		*/
+#define CONFIG_SYS_PROMPT		"=> "		/* Monitor Command Prompt	*/
+#define CONFIG_SYS_CBSIZE		256		/* Console I/O Buffer Size	*/
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)	/* Print Buffer Size	*/
+#define CONFIG_SYS_MAXARGS		16		/* max number of command args	*/
+#define CONFIG_SYS_BARGSIZE		CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/
+#define CONFIG_SYS_LOAD_ADDR		0x00100000	/* default load address		*/
+#define CONFIG_SYS_HZ			1000		/* decrementer freq: 1 ms ticks */
 
 /*-----------------------------------------------------------------------
  * PCI stuff
@@ -95,7 +95,7 @@
 
 #define CONFIG_NET_MULTI			/* Multi ethernet cards support */
 
-#define CFG_RX_ETH_BUFFER	8		/* use 8 rx buffer on eepro100	*/
+#define CONFIG_SYS_RX_ETH_BUFFER	8		/* use 8 rx buffer on eepro100	*/
 
 #define PCI_ENET0_IOADDR	0x80000000
 #define PCI_ENET0_MEMADDR	0x80000000
@@ -114,53 +114,53 @@
 /*-----------------------------------------------------------------------
  * Start addresses for the final memory configuration
  * (Set up by the startup code)
- * Please note that CFG_SDRAM_BASE _must_ start at 0
+ * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
  */
-#define CFG_SDRAM_BASE		0x00000000
-#define CFG_MAX_RAM_SIZE	0x02000000
+#define CONFIG_SYS_SDRAM_BASE		0x00000000
+#define CONFIG_SYS_MAX_RAM_SIZE	0x02000000
 
-#define CFG_RESET_ADDRESS	0xFFF00100
+#define CONFIG_SYS_RESET_ADDRESS	0xFFF00100
 
 #if defined (USE_DINK32)
-#define CFG_MONITOR_LEN		0x00030000
-#define CFG_MONITOR_BASE	0x00090000
-#define CFG_RAMBOOT		1
-#define CFG_INIT_RAM_ADDR	(CFG_MONITOR_BASE + CFG_MONITOR_LEN)
-#define CFG_INIT_RAM_END	0x10000
-#define CFG_GBL_DATA_SIZE	256  /* size in bytes reserved for initial data */
-#define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
+#define CONFIG_SYS_MONITOR_LEN		0x00030000
+#define CONFIG_SYS_MONITOR_BASE	0x00090000
+#define CONFIG_SYS_RAMBOOT		1
+#define CONFIG_SYS_INIT_RAM_ADDR	(CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
+#define CONFIG_SYS_INIT_RAM_END	0x10000
+#define CONFIG_SYS_GBL_DATA_SIZE	256  /* size in bytes reserved for initial data */
+#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
 #else
-#undef	CFG_RAMBOOT
-#define CFG_MONITOR_LEN		0x00030000
-#define CFG_MONITOR_BASE	TEXT_BASE
+#undef	CONFIG_SYS_RAMBOOT
+#define CONFIG_SYS_MONITOR_LEN		0x00030000
+#define CONFIG_SYS_MONITOR_BASE	TEXT_BASE
 
-#define CFG_GBL_DATA_SIZE	128
+#define CONFIG_SYS_GBL_DATA_SIZE	128
 
-#define CFG_INIT_RAM_ADDR     0x40000000
-#define CFG_INIT_RAM_END      0x1000
-#define CFG_GBL_DATA_OFFSET  (CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_RAM_ADDR     0x40000000
+#define CONFIG_SYS_INIT_RAM_END      0x1000
+#define CONFIG_SYS_GBL_DATA_OFFSET  (CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
 
 #endif
 
-#define CFG_FLASH_BASE		0xFFE00000
-#define CFG_FLASH_SIZE		(2 * 1024 * 1024)	/* Unity has onboard 1MByte flash */
+#define CONFIG_SYS_FLASH_BASE		0xFFE00000
+#define CONFIG_SYS_FLASH_SIZE		(2 * 1024 * 1024)	/* Unity has onboard 1MByte flash */
 #define CONFIG_ENV_IS_IN_FLASH	1
 #define CONFIG_ENV_OFFSET		0x00004000	/* Offset of Environment Sector */
 #define CONFIG_ENV_SIZE		0x00002000	/* Total Size of Environment Sector */
 
-#define CFG_MALLOC_LEN		(512 << 10)	/* Reserve 512 kB for malloc()	*/
+#define CONFIG_SYS_MALLOC_LEN		(512 << 10)	/* Reserve 512 kB for malloc()	*/
 
-#define CFG_MEMTEST_START	0x00000000	/* memtest works on		*/
-#define CFG_MEMTEST_END		0x02000000	/* 0 ... 32 MB in DRAM		*/
+#define CONFIG_SYS_MEMTEST_START	0x00000000	/* memtest works on		*/
+#define CONFIG_SYS_MEMTEST_END		0x02000000	/* 0 ... 32 MB in DRAM		*/
 
-#define CFG_EUMB_ADDR		0xFC000000
+#define CONFIG_SYS_EUMB_ADDR		0xFC000000
 
-#define CFG_ISA_MEM		0xFD000000
-#define CFG_ISA_IO		0xFE000000
+#define CONFIG_SYS_ISA_MEM		0xFD000000
+#define CONFIG_SYS_ISA_IO		0xFE000000
 
-#define CFG_FLASH_RANGE_BASE	0xFFE00000	/* flash memory address range	*/
-#define CFG_FLASH_RANGE_SIZE	0x00200000
+#define CONFIG_SYS_FLASH_RANGE_BASE	0xFFE00000	/* flash memory address range	*/
+#define CONFIG_SYS_FLASH_RANGE_SIZE	0x00200000
 #define FLASH_BASE0_PRELIM	0xFFE00000	/* processor board flash	*/
 
 /*
@@ -172,8 +172,8 @@
  */
 #define CONFIG_HARD_I2C		1		/* To enable I2C support	*/
 #undef	CONFIG_SOFT_I2C				/* I2C bit-banged		*/
-#define CFG_I2C_SPEED		400000		/* I2C speed and slave address	*/
-#define CFG_I2C_SLAVE		0x7F
+#define CONFIG_SYS_I2C_SPEED		400000		/* I2C speed and slave address	*/
+#define CONFIG_SYS_I2C_SLAVE		0x7F
 
 #ifdef CONFIG_SOFT_I2C
 #error "Soft I2C is not configured properly.  Please review!"
@@ -188,13 +188,13 @@
 #define I2C_DELAY		udelay(5)	/* 1/4 I2C clock duration */
 #endif /* CONFIG_SOFT_I2C */
 
-#define CFG_I2C_EEPROM_ADDR	0x57		/* EEPROM IS24C02		*/
-#define CFG_I2C_EEPROM_ADDR_LEN 1		/* Bytes of address		*/
-#define CFG_EEPROM_PAGE_WRITE_BITS	3
-#define CFG_EEPROM_PAGE_WRITE_DELAY_MS	10	/* and takes up to 10 msec */
+#define CONFIG_SYS_I2C_EEPROM_ADDR	0x57		/* EEPROM IS24C02		*/
+#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1		/* Bytes of address		*/
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS	3
+#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS	10	/* and takes up to 10 msec */
 
-#define CFG_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
-#define CFG_FLASH_BANKS		{ FLASH_BASE0_PRELIM }
+#define CONFIG_SYS_BAUDRATE_TABLE	{ 9600, 19200, 38400, 57600, 115200 }
+#define CONFIG_SYS_FLASH_BANKS		{ FLASH_BASE0_PRELIM }
 
 /*-----------------------------------------------------------------------
  * Definitions for initial stack pointer and data area (in DPRAM)
@@ -202,12 +202,12 @@
 
 
 #define CONFIG_WINBOND_83C553	1	/*has a winbond bridge			*/
-#define CFG_USE_WINBOND_IDE	0	/*use winbond 83c553 internal IDE ctrlr */
-#define CFG_WINBOND_ISA_CFG_ADDR    0x80005800	/*pci-isa bridge config addr	*/
-#define CFG_WINBOND_IDE_CFG_ADDR    0x80005900	/*ide config addr		*/
+#define CONFIG_SYS_USE_WINBOND_IDE	0	/*use winbond 83c553 internal IDE ctrlr */
+#define CONFIG_SYS_WINBOND_ISA_CFG_ADDR    0x80005800	/*pci-isa bridge config addr	*/
+#define CONFIG_SYS_WINBOND_IDE_CFG_ADDR    0x80005900	/*ide config addr		*/
 
-#define CFG_IDE_MAXBUS		2   /* max. 2 IDE busses	*/
-#define CFG_IDE_MAXDEVICE	(CFG_IDE_MAXBUS*2) /* max. 2 drives per IDE bus */
+#define CONFIG_SYS_IDE_MAXBUS		2   /* max. 2 IDE busses	*/
+#define CONFIG_SYS_IDE_MAXDEVICE	(CONFIG_SYS_IDE_MAXBUS*2) /* max. 2 drives per IDE bus */
 
 /* TODO: Change this to VIA686A */
 
@@ -216,40 +216,40 @@
  */
 #define CONFIG_NS87308			/* Nat Semi super-io controller on ISA bus */
 
-#define CFG_NS87308_BADDR_10	1
+#define CONFIG_SYS_NS87308_BADDR_10	1
 
-#define CFG_NS87308_DEVS	( CFG_NS87308_UART1   | \
-				  CFG_NS87308_UART2   | \
-				  CFG_NS87308_POWRMAN | \
-				  CFG_NS87308_RTC_APC )
+#define CONFIG_SYS_NS87308_DEVS	( CONFIG_SYS_NS87308_UART1   | \
+				  CONFIG_SYS_NS87308_UART2   | \
+				  CONFIG_SYS_NS87308_POWRMAN | \
+				  CONFIG_SYS_NS87308_RTC_APC )
 
-#undef	CFG_NS87308_PS2MOD
+#undef	CONFIG_SYS_NS87308_PS2MOD
 
-#define CFG_NS87308_CS0_BASE	0x0076
-#define CFG_NS87308_CS0_CONF	0x30
-#define CFG_NS87308_CS1_BASE	0x0075
-#define CFG_NS87308_CS1_CONF	0x30
-#define CFG_NS87308_CS2_BASE	0x0074
-#define CFG_NS87308_CS2_CONF	0x30
+#define CONFIG_SYS_NS87308_CS0_BASE	0x0076
+#define CONFIG_SYS_NS87308_CS0_CONF	0x30
+#define CONFIG_SYS_NS87308_CS1_BASE	0x0075
+#define CONFIG_SYS_NS87308_CS1_CONF	0x30
+#define CONFIG_SYS_NS87308_CS2_BASE	0x0074
+#define CONFIG_SYS_NS87308_CS2_CONF	0x30
 
 /*
  * NS16550 Configuration
  */
-#define CFG_NS16550
-#define CFG_NS16550_SERIAL
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
 
-#define CFG_NS16550_REG_SIZE	1
+#define CONFIG_SYS_NS16550_REG_SIZE	1
 
 #if (CONFIG_CONS_INDEX > 2)
-#define CFG_NS16550_CLK		CONFIG_DRAM_SPEED*1000000
+#define CONFIG_SYS_NS16550_CLK		CONFIG_DRAM_SPEED*1000000
 #else
-#define CFG_NS16550_CLK		1843200
+#define CONFIG_SYS_NS16550_CLK		1843200
 #endif
 
-#define CFG_NS16550_COM1	(CFG_ISA_IO + CFG_NS87308_UART1_BASE)
-#define CFG_NS16550_COM2	(CFG_ISA_IO + CFG_NS87308_UART2_BASE)
-#define CFG_NS16550_COM3	(CFG_EUMB_ADDR + 0x4500)
-#define CFG_NS16550_COM4	(CFG_EUMB_ADDR + 0x4600)
+#define CONFIG_SYS_NS16550_COM1	(CONFIG_SYS_ISA_IO + CONFIG_SYS_NS87308_UART1_BASE)
+#define CONFIG_SYS_NS16550_COM2	(CONFIG_SYS_ISA_IO + CONFIG_SYS_NS87308_UART2_BASE)
+#define CONFIG_SYS_NS16550_COM3	(CONFIG_SYS_EUMB_ADDR + 0x4500)
+#define CONFIG_SYS_NS16550_COM4	(CONFIG_SYS_EUMB_ADDR + 0x4600)
 
 /*
  * Low Level Configuration Settings
@@ -259,27 +259,27 @@
 
 #define CONFIG_SYS_CLK_FREQ  33333333	/* external frequency to pll */
 
-#define CFG_ROMNAL		7	/*rom/flash next access time		*/
-#define CFG_ROMFAL		11	/*rom/flash access time			*/
+#define CONFIG_SYS_ROMNAL		7	/*rom/flash next access time		*/
+#define CONFIG_SYS_ROMFAL		11	/*rom/flash access time			*/
 
-#define CFG_REFINT	430	/* no of clock cycles between CBR refresh cycles */
+#define CONFIG_SYS_REFINT	430	/* no of clock cycles between CBR refresh cycles */
 
 /* the following are for SDRAM only*/
-#define CFG_BSTOPRE	121	/* Burst To Precharge, sets open page interval */
-#define CFG_REFREC		8	/* Refresh to activate interval		*/
-#define CFG_RDLAT		4	/* data latency from read command	*/
-#define CFG_PRETOACT		3	/* Precharge to activate interval	*/
-#define CFG_ACTTOPRE		5	/* Activate to Precharge interval	*/
-#define CFG_ACTORW		3	/* Activate to R/W			*/
-#define CFG_SDMODE_CAS_LAT	3	/* SDMODE CAS latency			*/
-#define CFG_SDMODE_WRAP		0	/* SDMODE wrap type			*/
+#define CONFIG_SYS_BSTOPRE	121	/* Burst To Precharge, sets open page interval */
+#define CONFIG_SYS_REFREC		8	/* Refresh to activate interval		*/
+#define CONFIG_SYS_RDLAT		4	/* data latency from read command	*/
+#define CONFIG_SYS_PRETOACT		3	/* Precharge to activate interval	*/
+#define CONFIG_SYS_ACTTOPRE		5	/* Activate to Precharge interval	*/
+#define CONFIG_SYS_ACTORW		3	/* Activate to R/W			*/
+#define CONFIG_SYS_SDMODE_CAS_LAT	3	/* SDMODE CAS latency			*/
+#define CONFIG_SYS_SDMODE_WRAP		0	/* SDMODE wrap type			*/
 #if 0
-#define CFG_SDMODE_BURSTLEN	2	/* OBSOLETE!  SDMODE Burst length 2=4, 3=8		*/
+#define CONFIG_SYS_SDMODE_BURSTLEN	2	/* OBSOLETE!  SDMODE Burst length 2=4, 3=8		*/
 #endif
 
-#define CFG_REGISTERD_TYPE_BUFFER   1
-#define CFG_EXTROM 1
-#define CFG_REGDIMM 0
+#define CONFIG_SYS_REGISTERD_TYPE_BUFFER   1
+#define CONFIG_SYS_EXTROM 1
+#define CONFIG_SYS_REGDIMM 0
 
 
 /* memory bank settings*/
@@ -289,93 +289,93 @@
  * bits will be set to 0x00000 for a start address, or 0xfffff for an
  * end address
  */
-#define CFG_BANK0_START		0x00000000
-#define CFG_BANK0_END		(CFG_MAX_RAM_SIZE - 1)
-#define CFG_BANK0_ENABLE	1
-#define CFG_BANK1_START		0x3ff00000
-#define CFG_BANK1_END		0x3fffffff
-#define CFG_BANK1_ENABLE	0
-#define CFG_BANK2_START		0x3ff00000
-#define CFG_BANK2_END		0x3fffffff
-#define CFG_BANK2_ENABLE	0
-#define CFG_BANK3_START		0x3ff00000
-#define CFG_BANK3_END		0x3fffffff
-#define CFG_BANK3_ENABLE	0
-#define CFG_BANK4_START		0x00000000
-#define CFG_BANK4_END		0x00000000
-#define CFG_BANK4_ENABLE	0
-#define CFG_BANK5_START		0x00000000
-#define CFG_BANK5_END		0x00000000
-#define CFG_BANK5_ENABLE	0
-#define CFG_BANK6_START		0x00000000
-#define CFG_BANK6_END		0x00000000
-#define CFG_BANK6_ENABLE	0
-#define CFG_BANK7_START		0x00000000
-#define CFG_BANK7_END		0x00000000
-#define CFG_BANK7_ENABLE	0
+#define CONFIG_SYS_BANK0_START		0x00000000
+#define CONFIG_SYS_BANK0_END		(CONFIG_SYS_MAX_RAM_SIZE - 1)
+#define CONFIG_SYS_BANK0_ENABLE	1
+#define CONFIG_SYS_BANK1_START		0x3ff00000
+#define CONFIG_SYS_BANK1_END		0x3fffffff
+#define CONFIG_SYS_BANK1_ENABLE	0
+#define CONFIG_SYS_BANK2_START		0x3ff00000
+#define CONFIG_SYS_BANK2_END		0x3fffffff
+#define CONFIG_SYS_BANK2_ENABLE	0
+#define CONFIG_SYS_BANK3_START		0x3ff00000
+#define CONFIG_SYS_BANK3_END		0x3fffffff
+#define CONFIG_SYS_BANK3_ENABLE	0
+#define CONFIG_SYS_BANK4_START		0x00000000
+#define CONFIG_SYS_BANK4_END		0x00000000
+#define CONFIG_SYS_BANK4_ENABLE	0
+#define CONFIG_SYS_BANK5_START		0x00000000
+#define CONFIG_SYS_BANK5_END		0x00000000
+#define CONFIG_SYS_BANK5_ENABLE	0
+#define CONFIG_SYS_BANK6_START		0x00000000
+#define CONFIG_SYS_BANK6_END		0x00000000
+#define CONFIG_SYS_BANK6_ENABLE	0
+#define CONFIG_SYS_BANK7_START		0x00000000
+#define CONFIG_SYS_BANK7_END		0x00000000
+#define CONFIG_SYS_BANK7_ENABLE	0
 /*
  * Memory bank enable bitmask, specifying which of the banks defined above
  are actually present. MSB is for bank #7, LSB is for bank #0.
  */
-#define CFG_BANK_ENABLE		0x01
+#define CONFIG_SYS_BANK_ENABLE		0x01
 
-#define CFG_ODCR		0xff	/* configures line driver impedances,	*/
+#define CONFIG_SYS_ODCR		0xff	/* configures line driver impedances,	*/
 					/* see 8240 book for bit definitions	*/
-#define CFG_PGMAX		0x32	/* how long the 8240 retains the	*/
+#define CONFIG_SYS_PGMAX		0x32	/* how long the 8240 retains the	*/
 					/* currently accessed page in memory	*/
 					/* see 8240 book for details		*/
 
 /* SDRAM 0 - 256MB */
-#define CFG_IBAT0L	(CFG_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
-#define CFG_IBAT0U	(CFG_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_IBAT0L	(CONFIG_SYS_SDRAM_BASE | BATL_PP_10 | BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT0U	(CONFIG_SYS_SDRAM_BASE | BATU_BL_256M | BATU_VS | BATU_VP)
 
 /* stack in DCACHE @ 1GB (no backing mem) */
 #if defined(USE_DINK32)
-#define CFG_IBAT1L	(0x40000000 | BATL_PP_00 )
-#define CFG_IBAT1U	(0x40000000 | BATU_BL_128K )
+#define CONFIG_SYS_IBAT1L	(0x40000000 | BATL_PP_00 )
+#define CONFIG_SYS_IBAT1U	(0x40000000 | BATU_BL_128K )
 #else
-#define CFG_IBAT1L	(CFG_INIT_RAM_ADDR | BATL_PP_10 | BATL_MEMCOHERENCE)
-#define CFG_IBAT1U	(CFG_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
+#define CONFIG_SYS_IBAT1L	(CONFIG_SYS_INIT_RAM_ADDR | BATL_PP_10 | BATL_MEMCOHERENCE)
+#define CONFIG_SYS_IBAT1U	(CONFIG_SYS_INIT_RAM_ADDR | BATU_BL_128K | BATU_VS | BATU_VP)
 #endif
 
 /* PCI memory */
-#define CFG_IBAT2L	(0x80000000 | BATL_PP_10 | BATL_CACHEINHIBIT)
-#define CFG_IBAT2U	(0x80000000 | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_IBAT2L	(0x80000000 | BATL_PP_10 | BATL_CACHEINHIBIT)
+#define CONFIG_SYS_IBAT2U	(0x80000000 | BATU_BL_256M | BATU_VS | BATU_VP)
 
 /* Flash, config addrs, etc */
-#define CFG_IBAT3L	(0xF0000000 | BATL_PP_10 | BATL_CACHEINHIBIT)
-#define CFG_IBAT3U	(0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP)
+#define CONFIG_SYS_IBAT3L	(0xF0000000 | BATL_PP_10 | BATL_CACHEINHIBIT)
+#define CONFIG_SYS_IBAT3U	(0xF0000000 | BATU_BL_256M | BATU_VS | BATU_VP)
 
-#define CFG_DBAT0L	CFG_IBAT0L
-#define CFG_DBAT0U	CFG_IBAT0U
-#define CFG_DBAT1L	CFG_IBAT1L
-#define CFG_DBAT1U	CFG_IBAT1U
-#define CFG_DBAT2L	CFG_IBAT2L
-#define CFG_DBAT2U	CFG_IBAT2U
-#define CFG_DBAT3L	CFG_IBAT3L
-#define CFG_DBAT3U	CFG_IBAT3U
+#define CONFIG_SYS_DBAT0L	CONFIG_SYS_IBAT0L
+#define CONFIG_SYS_DBAT0U	CONFIG_SYS_IBAT0U
+#define CONFIG_SYS_DBAT1L	CONFIG_SYS_IBAT1L
+#define CONFIG_SYS_DBAT1U	CONFIG_SYS_IBAT1U
+#define CONFIG_SYS_DBAT2L	CONFIG_SYS_IBAT2L
+#define CONFIG_SYS_DBAT2U	CONFIG_SYS_IBAT2U
+#define CONFIG_SYS_DBAT3L	CONFIG_SYS_IBAT3L
+#define CONFIG_SYS_DBAT3U	CONFIG_SYS_IBAT3U
 
 /*
  * For booting Linux, the board info and command line data
  * have to be in the first 8 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization.
  */
-#define CFG_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
+#define CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux */
 /*-----------------------------------------------------------------------
  * FLASH organization
  */
-#define CFG_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
-#define CFG_MAX_FLASH_SECT	36	/* max number of sectors on one chip	*/
+#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
+#define CONFIG_SYS_MAX_FLASH_SECT	36	/* max number of sectors on one chip	*/
 
-#define CFG_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
-#define CFG_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
+#define CONFIG_SYS_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
+#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
 
 /*-----------------------------------------------------------------------
  * Cache Configuration
  */
-#define CFG_CACHELINE_SIZE	32	/* For MPC8240 CPU			*/
+#define CONFIG_SYS_CACHELINE_SIZE	32	/* For MPC8240 CPU			*/
 #if defined(CONFIG_CMD_KGDB)
-#  define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value */
+#  define CONFIG_SYS_CACHELINE_SHIFT	5	/* log base 2 of the above value */
 #endif
 
 /*